COEF PERFORMANCE 250DV DV User Manual Page 73
- Page / 129
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ScancommanderScancommander
ScancommanderScancommander
Scancommander
eMail: [email protected]
.
Tel.: +49 931 497940
.
User's Manual Scancommander
7373
7373
73
10. Inputs and outputs
The Scancommander can be connected to an AC Powersource between 90
and 240 Volt AC (40-60Hz).
The powerswitch is located on the front panel at the top right hand side.
The DMX output conforms to USITT DMX 1990. Every unit using this protocol
can be successfully interfaced with the Scancommander.
The DMX Output is optically isolated and exceeds the RS485 Norm.
Pinout: pin 1 = Shield
pin 2 = Data -
pin 3 = Data +
pin 4 = not connected
pin 5 = not connected
The DMX Input allows operation of two different functions:
a. All incoming DMX-Data will be merged with the Data produced by the
Scancommander. The highest value takes precedence at the DMX output.
b. To remote various functions of the Scancommander via DMX, e.g. coupling
a lightning desk and a Scancommander. For configuration see “Remote”.
The connector is a Mono or Stereo Phone Jack 6,3mm and the input is
galvanic insulated. Input impedance is ca. 3K Ohm, the threshold is min. 3
mV. The electrical connection is tip and sleeve. The Sound Input controls are
located on the upper left side of the front panel.
Adjustment: Turn the volume control until the left LED begins to light; higher
inputs are limited automatically. To get the best results, the frequency
control should be turned to the left for low frequencies (50 Hz), to the right
for high frequencies (2 kHz). ”Hold-Off” control should be initially set full
left.
To avoid double triggering of a bass drum for example, rotate “Hold Off” as
needed. At full right, “Hold Off” time is a full six seconds.
The Sound Input doubles as the Time Code Input.
The electrical connection is the ring + common (galvanic insulated). The input
impedance is ca. 3 kOhm, the minimal level ca.200mV.
The Remote Go input is a 6.3 mm Phone Jack connector.
a) For electrical contact-switch use the ring and tip.
b) For 5 Volt Impulse use the tip and common.
Danger! Maximum 5 Volt at this input; a higher voltage may damage the
Scancommander.
The connection is a 25 pin Sub-D.
Mains (Power Supply)
DMX 512 output
DMX 512 input
Sound input
SMPTE Time Code
Remote GO input
- SCANCOMMANDER 1
- Contents 2
- 1.1 General remarks 5
- 1.3 Installation 6
- 1.2 Specifications and extras 6
- 2. Setup 7
- 2.2 Lamp type 8
- DMX MOVEMENT 10
- SCAN Selection 10
- CHANGE PAN<>TILT 10
- INVERT PAN or INVERT TILT 10
- ! Attention ! 12
- ! STORE ! 12
- 3.2.1 Tuning with the encoder 14
- 3.2.2 Programming of presets 15
- 3.2.3 Playback of presets 16
- 3.3 Movements 18
- Transforming programs to 20
- Adjusting preset positions 20
- Transforming direct DMX 20
- 3.3.4 Trackball and Mouse 21
- 3.3.5 Followspot mode 21
- 3.3.7 Movement speed 23
- 4. Memories 24
- 4.2 Playback memories 26
- 4.2.5 Display of Memory Names 28
- 4.3 Selective memories 29
- 4.4 Modifying of memories 31
- 4.4.3 Copying memories 32
- 5. Chaser 33
- 5.2 Playback chasers 35
- On Line changing of the 36
- 6. Sequences 40
- 6.2 Playback of sequences 43
- 6.2.6 Enable Sequence 45
- 6.2.7 Sequence playback menu 46
- Changing channel values 50
- Testing single steps 50
- 7. REMOTE 52
- 7.1 Remote via Touchboard 53
- 7.2 Remote via DMX input 54
- DMX 23 54
- 7.3 MIDI 55
- 7.4 Master-Slave Operation 56
- 7.5 SMPTE TIME CODE 57
- 00:00:01:15 58
- 00:00:12:23 59
- 7.5.3 Time Code Playback 60
- 00:00:12:15 61
- INSERT NOT POSSIBLE 62
- 8. Dimmer and color changers 64
- 8.4 EXTRA presets 65
- !! ATTENTION !! 66
- 9. Utilities 67
- 9.2 Storage of programs 68
- 9.3 Clearing programs 70
- 9.4 Keyswitch 70
- 9.5 Macros 71
- 9.5.2 Macro user examples 72
- 10. Inputs and outputs 73
- ATTENTION!! 74
- 11. Defining your own Scans 75
- CHAN. 1 GOBO 2 76
- CHANNEL DIMMER 77
- BRIGHTNESS: 77
- Appendix 1: 89
- Manufacturer CLAY PAKY 90
- Manufacturer COEMAR 94
- Manufacturer FLY 100
- Manufacturer FUTURELIGHT 100
- ScancommanderScancommander 101
- Scancommander 101
- Manufacturer GLP 102
- Manufacturer LAMPO 106
- Manufacturer LICHT TECHNIK 106
- Manufacturer LITEBEAM 106
- Manufacturer SAGITTER 114
- Manufacturer SUMMA 118
- Standard COLOR CHANGER 122
- 3. DMX address 124
- Tel.: +49 931 497940 125
- 6. Homing function 126
- Safety Instructions: 128
- DECLARATION OF CONFORMITY 129
Related products and manuals for Floodlights COEF PERFORMANCE 250DV DV
(129 pages)
Floodlights COEF MP250 FRESNEL User Manual
(20 pages)
(20 pages)
Floodlights COEF EMULATION WRGB User Manual
(131 pages)
(131 pages)
© 2020, manymanuals.com. All rights reserved. | 1.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals